Home Appliance Repair: Steps in the Replacement of a Dryer Ignitor

Every gas dryer is equipped with an ignitor that produces a flame from the gas supply. A broken ignitor prevents the dryer from producing any heat, thus making drying your clothes impossible. Replacing a broken ignitor is not really as hard as it may seem, but it does require some reading and planning. This article will give the readers some basic steps to execute replacement of a broken dryer ignitor Dryer Repair Los Angeles.

Before proceeding with the repair and replacement steps, make sure that you get the correct ignitor for your dryer. To do this, check and take note of your dryer model number. You will need this information (unit model number) in your purchase at an appliance repair store. The model number will assist the technician in the store to find the proper parts for your specific dryer unit. It is important to remember that the elements on the ignitor are very sensitive, proper handling is a must. Some of the steps below may get too technical, so if you are feeling a bit uncomfortable, you can always call your trusted repair man to do the job.

Step 1
Disconnect the dryer’s power cord from its electrical outlet. Close the gas supply valve on the gas line leading to the diver.

Step 2
Lift the lint screen out off its compartment. Remove the two screws next to the lint screen compartment.

Step 3
Insert a putty knife into the gap between the top panel and the front of the dryer. Press the putty knife into the top panel clips 2 inches from each front corner.

Step 4
Disconnect the wiring harness that connects to the flame sensor on the burner can. The wirings can be easily removed using your hands.

How To Take Apart A Dryer – Samsung Dryer Repair Help

The necessary steps involved to tear apart a Samsung dryer are relatively simple. Before taking the dryer apart you want to unplug or disconnect power to the dryer first.

Pull the dryer forward because the top is held down with two screws coming in from the back. Remove the screws and the top will slide back and off.

With the top off, the control panel will be accessible. The control is clipped into plastic clips, there are no screws to remove the control panel. With the panel Un-clipped, you will see the wire harness that needs to be disconnected. Depress the wire harness tab and the control will pull free.

Remove the two screws that are located on the lint filter housing near the bottom of the door opening. The screws that were hidden by the base of the control panel will need to be removed along the top of the front panel.

When the screws are off, depress the two clips that hold the front to the cabinet and pull the front panel forward to reveal the door switch. Now that you have access to the door switch, Un-clip the door switch and the front panel will lift up and off the unit. Samsung does not place screws on the lower front panel; the panel sits in a metal groove dryer repair van nuys.

Samsung uses a bulkhead on the front of their units, remove the four screws that are holding the bulkhead to the cabinet.

There are 2 screws along the left side and 2 on the right side. Once the screws are removed, the bulkhead will lift out of the holding slot enabling access to the dryer belt. Notice the routing of the belt before removal, using a camera or drawing will help you assembly if dryer belt routing is forgotten.

With the belt removed, the drum will lift up and out of the dryer and give you access to the all of the components. Now you can use your volt and ohm meter to diagnose the unit properly for whatever electrical/heating issues you may be having.

Samsung dryers are a bit different from American built dryers. Samsung uses different technology in both their washer and dryers that a Whirlpool or Maytag washer or dryer does not have. This is good and bad, often the components that cause a dryer to stop working are extra options that are present that a different brand doesn’t have. On most residential washer and dryers they come equipped with what is known as a PCB board. This board is what is behind the buttons that you press to start the dryer. When an option goes that doesn’t prevent the dryer from starting the only way to fix it is to replace the main control board.

Make Clothes Dryer More Efficient by Recycling the Heat

As the cost of electricity continues to skyrocket consumers are looking for new ideas to help get the most value out of their appliances. This includes the electric clothes dryer.

Although consumption cannot be lowered there is a device to take advantage of the heat it produces. It is called a dryer heat recycler. It has proven to be a winner in the fight to be more energy efficient.

A heat recycler does just what its name indicates. It allows the warm air from the household electric clothes dryer to be redirected back into the laundry room. This is an added bonus if the laundry room is in a cold basement. Plus the heat is free.

The theory behind the recycler is simple. It uses the hot air from the electric dryer to heat the laundry room. In this way the room vent can be closed down. Hence lowering your heating costs.

The element in an electric dryer is approximately 5000 watts. This is equivalent to a couple of baseboard heaters. The temperature of the air leaving an electric dryer is about 130 degrees Fahrenheit. So why waste it – instead, put it to work for you.

For an investment of about $15 the hot air your dryer normally dumps outside can be directed back into the house. We have been successfully suggesting these to clients for years.

There is a plastic handle on the side to direct the air either inside or outside. In the winter months the handle is adjusted to direct the hot air into the house. In the summer the air is directed back outside.

The heat recycler is easy to install. It is usually mounted (screws are provided) to a wall or beam behind, and slightly above, the dryer console area. Once mounted the dryer venting can be cut and reattached to the device. Follow the instructions to maintain proper airflow direction. The recycler does have an “in” and an “out”. Always mount the recycler for easy access by all family members. If mounted in an awkward place no one will clean the filter.

Before purchase make sure the model you buy comes complete with two venting clamps. Some less expensive ones don’t include the clamps. Clamps are vital for a proper installation. Do not be tempted to attach the venting sections to the recycler with duct tape. It will dry out and cause the venting to fall off. If required invest in two good quality metal vent clamps. A couple of four-inch clamps will cost about three dollars.

The recycler has a built-in filter screen that needs to be cleaned just like the one inside the dryer. We prefer the type that has a mesh screen filter as opposed to the one with a sock-like filter. It is a couple of dollars more but the metal filter is more durable and a lot easier to clean than the cotton type samsung dryer repair los angeles.

So once the recycler is mounted and secured give it a test run. Set the temperature selector to hot and start dryer. Allow dryer to run a few minutes. Test that the air comes inside when the handle is in the winter position. Next, move handle to summer position. Air should then be seen to go outdoors. Go outside and confirm air freely escapes outdoors. If not the screen in the outdoor vent cap may be blocked with lint. Or the vent cap flapper valve may be sticking. Go back indoors and test all joints for air leakage. If leaking air, tape joints with duct tape.

From then on all that is required is to clean the heat recycler filter every few laundry loads. Plus, twice a year turn the handle to redirect the airflow. Not much work to get all that nice free hot air for your home.

Note that throughout this article I have been using the term electrical clothes dryer. The heat recycler cannot be used with a gas clothes dryer. The venting pipe of a gas dryer must not be opened or redirected. Small amounts of gas vapour and carbon monoxide may be present in the outlet air of a gas clothes dryer. Therefore, for safety reasons, the heat recycler cannot be used with a gas dryer.

Tools in Appliances Repairs

Appliances are among the easy to obtain investments. Some are available at a low price while some branded appliances can really cost a fortune. But whatever the brand or the price of these appliances, at some point they will malfunction and wear down. When that happens, we try to repair and fix them either by doing it ourselves or by taking the appliances to a professional repairman. Either way, there are certain tools which are indispensable equipments in restoring the broken appliances.

A variety of meters including Ohmmeter, Voltmeter and Ammeter are the major tools in appliance repair. The ohm meter, available in micro and mega, is for measuring large and small amounts of electrical resistance or the opposition to electrical current. The quantity of electrical potential difference from two points in the electrical circuit is gauged by a volt meter. The ammeter is the device utilized in measuring the electric current in a circuit. There is also a device called the multi tester which integrates a voltmeter and an ohmmeter and effectively combines several measurement functions in a single meter Kenmore Appliance Repair Los Angeles.

A set of adjustable wrenches is very much needed in repairing appliances. A wrench, or a spanner, is a hand tool that adds extra force in mechanically working with application of torque to turn a nut or bolt. Wrenches are of various sizes, shapes and forms. Commonly used wrenches or spanners are Open-end wrench, ring spanner, combination wrench/spanner, flare nut wrench, monkey wrench, pipe wrench, socket wrench, torque wrench, box spanner and striking face box wrench.

The nut river set for specific usage in appliance repair must have at least 7 elements or pieces. A nut driver is a tool for fastening nuts and bolts. In essence, a nut driver is composed of a socket attached to a shaft and cylindrical handle, like in a screwdriver that is also a useful tightening tool.

A Screwdriver set for use in repairing appliances needs to contain about 4-6 screwdrivers. The screwdriver has a head and a tip that engages the screw in applying torque. This tools is a long, straight hand device whose head is flat and narrow to be able to fit in screws. There are also Phillips head type of screwdrivers whose tips look like a star.

A hose clamp pliers is known to already been around even before the birth of the other tools. This basic hand tool is employed in placing and removing spring tension hose clamps that are found in appliance drains and fill hoses. The handles or knobs are usually made with wax or dipped in plastic to allow fast and easy gripping.

Recommendations and Online Research Can Help You Choose a Reputable Appliance Repair Service

Considering that many home appliances get used almost every day, it’s inevitable that your household will need an appliance repair service at least every couple of years. Name-brand appliances are usually durable and last along time, but regular wear and tear will take their toll on even the best kitchen or laundry room appliances.

What do you do when an appliance stops working or shows signs of diminished performance? In a perfect world, you would already have an established relationship with a reasonably priced, readily available appliance repair service that consistently does high-quality work. In our less-than-perfect world, it’s sometimes necessary to make a few phone calls, do a little research on the Internet, or get referrals from people you know. While there’s always an element of risk in trying out an appliance repair service that you’re unfamiliar with, there are a number of things you can do to drastically reduce the risk.

One of the most reliable ways to get a referral of a reputable appliance repair company, whether you need washing machine repairs or refrigerator repair, is to get a recommendation from someone you know and trust. Among your coworkers, neighbors, family, and friends, it shouldn’t be too difficult to get the name of a dependable washer/dryer repair service, for example, that won’t charge you an arm and a leg for good service. In the majority of cases, a broken appliance would not be considered an emergency, so the best strategy is to maintain your composure and avoid scheduling a service call with the first repair service you stumble across in the yellow pages or on the Internet dryer repair los angeles.

If your network of friends and acquaintances is not coming through for you with the name of a great oven repair service or garbage disposal repair technician, you can search on the Internet for dishwasher repairs, oven repair, or whatever appliance repair you need. When reviewing different Web sites, you could narrow down your list of possibilities to only those companies or individuals that are licensed and/or insured, factory trained or factory authorized, and who offer some sort of written warranty or guarantee on parts, labor, and customer satisfaction. Warranties on appliance repairs, such as 30 days on labor and 90 days on appliance parts, can be an indication of quality and good customer service. Number of years of experience is also a possible indicator of reliability when you’re in the market for major appliance repair services.

Last, but not least, it can be revealing to look up an appliance repair company’s record on the Better Business Bureau’s Web site. If the company you’re considering is listed in the BBB’s database, then they’ll be given a grade on a scale of A+ to F. The number of complaints that have been filed against the business, the nature of the complaints, and whether or not they’ve been resolved are all part of each business review that can be found at bbb.org. The Better Business Bureau ratings are based on a total of 16 factors, including the length of time the business has been operating. Whether you’re researching a company that does washing machine repair or water heater repair, the BBB can provide you with a lot of useful information about the company’s background and customer service record.