DIY Water Heater System Maintenance For The Homeowner

Water heaters are among our most valuable appliances at home. They provide us with warm, relaxing baths; help us thoroughly clean our dirty clothes; wash our greasy pots and pans and many more. This appliance is indeed worthy of every penny we’ve invested on it, considering the convenience that it consistently brings. And with proper care and maintenance, it will surely last for more than 10 years. Here are some tips that you have to follow when taking care of your water heating system at home samsung appliance repair pasadena.

1. Check the Temperature and Pressure Valve (T&P valve).

The water heater tank seals in high amounts of temperature and pressure to keep the water warm. Once in a while, you’ll have to relieve the pressure to prevent the tank from exploding or leaking. To accomplish this maintenance task, locate the T&P valve which is commonly situated at the side or on top of the heating tank. Carefully lift the rocker arm. If it won’t budge at all, it needs to be replaced immediately. If it won’t snap back down after lifting, it must be loosened.

2. Keep the temperature at 120 degrees Fahrenheit.

Setting the appliance’s temperature higher than that may result to accidents such as scalding. Also remember that for every 10 degrees that you lower the temp, you’ll be saving up to 5% on your energy consumption.

3. Maintain a clearance space of 2 feet around the tank.

Unless otherwise stated on your appliance’s user’s manual, you have to set a clear space of 2 feet around the unit. This should avoid the onset of fire-related accidents.

4. Inspect the anode rod.

The anode rod is that piece of magnesium or aluminum stick that’s dipped into the water heater tank. Its main purpose is to protect the water storage from corrosion. Rust cannot be prevented but instead of letting it eat away on the tank, it will instead eat away on the anode rod. Make sure that the rod is replaced when about 6 inches of its core wire is already bare; when it’s coated with calcium or when it is less than half an inch thick.

5. Insulate the pipes.

Insulating the pipes will help improve the appliance’s efficiency. While this is a must on older water heating units, you should know that new ones already come equipped with insulation. You should never skip this part especially during cold winter months, when heating water becomes a bit difficult for the appliance.

6. Insulate the tank.

To lessen the amount of standby heat loss and instead keep the water in the storage tank warm, you should also insulate the tank. You can use an insulating jacket, a R.4.5 foil-covered bubble wrap, for this task. Just don’t cover the top part of your gas or oil water heater.

7. Flush it!

Don’t forget to drain your water heater tank two to three times a year. As you can see, every time that water fills the tank, sediments, minerals and debris also get in and accumulate at the bottom of the water storage. These sediments should be removed to help the appliance perform efficiently and also to keep it in good condition.

Common Refrigerator Faults

The refrigerator is perhaps one of the most important appliances in the kitchen because not only does it store food, but it also keeps it from spoiling. Without it, you would have to do your grocery shopping everyday which would be a big inconvenience.

Unfortunately, this scenario is very possible if your refrigerator breaks down and if that is the case, you need to contact a repair technician right away. Not every problem or fault needs to be attended to by a technician because there are things that you can easily troubleshoot on your own. For instance, when it is not cooling the food as it is supposed to, you can just check if there is any dirt or particles that are blocking the air flow ducts maytag refrigerator repair pasadena.

There are some common refrigerator problems that do warrant repair. A refrigerator should have a gentle humming sound that assures you that all is well and hearty but if it creaks, groans or croaks, or when the noise is a nuisance, then it means there is a problem. You should immediately get in touch with a technician to determine what is wrong and have it rectified.

It is a common problem to find a leaking refrigerator and this can even flood your kitchen floor. The water comes from different sources inside the refrigerator. All of them have an ice or water dispenser, but there could be specific lines in them that are broken and will need replacement. If there is a drain pan or defrost tray underneath, then you should check for cracks and holes. When the refrigerator does not cool as it is supposed to, then this is a clear indication that something is wrong.

You should ensure that the temperature is set between 38 to 40 degrees Fahrenheit and adjust the thermostat controller appropriately. After 6 hours, the temperature should change but if that is not the case, then you should check if the fan is running. If all fails, you should try to defrost the refrigerator by turning it off and leaving the doors open all night long.

In the morning, you should replace the food and turn it on, check that the thermostat is set in the middle setting and after 6 hours, check the temperature. If this fails, then it is time to call a repair service provider to have a look and identify what the problem is. When the light is on but the unit is not running, then this means that the compressor is faulty and will need to be replaced.

However, before the replacement, you should consult with a professional so that other causes like a faulty starter relay and temperature control unit can be ruled out. The compressor is an integral component of the refrigerator and most of the faults may originate from it. You should never tinker with the motor of the compressor even when the unit is off because you may end up causing more problems. Having a professional to check any faults in a refrigerator ensures that the right cause of action is taken, and the problem is successfully rectified.

Repair and Cleaning Clothes Dryer

You can do two other things with a clothes dryer apart from drying clothes: cleaning and repairing the machine if it breaks down. A clothes dryer is a home appliance, and like your typical home appliance, it needs regular cleaning and maintenance if you want it to do a good job. Clothes dryers are sturdy machines, but that’s not saying they don’t choke and break down sometimes, because they do. Put your helmet on because it’s time to do a little cleaning and repairing.

According to the US Consumer Product Safety Commission (CPSC), clothes dryers are responsible for around 15,500 fires annually dryer repair altadena.

It is obvious then that you should take good care of your clothes dryer. Continuous use of this appliance allows lint to build up in the machine and along the walls of the hose, where the water drains out. Not cleaning the machine and allowing lint to accumulate over long periods of time, according to the CPSC, cause the clothes dryer to overheat, increasing the chances of starting a fire.

Clean the clothes dryer regularly and make sure to remove all traces of lint stuck in the lint filter. Also, improper venting can cause damage to the machine. A clogged clothes dryer shows the following symptoms: long drying times, noisy operation, clothes that are still damp and hot even after drying, and non-functioning automatic sensors.

Most problems with clothes dryers are related to the heat source or the motor that tumbles the clothes. One way or the other, it isn’t a very good idea to just open up the machine and start poking the parts every which way-you need a professional repair man to do this. These guys will troubleshoot and repair the problem for a small price, free if covered by the warranty. It is always better to be safe than sorry.

Dryer Repair Basics

Dryer Repair Tips and Information

Repairing a dryer can be a rewarding experience for the professional or a home do-it-yourselfer. You can save money and gain valuable knowledge and know-how. Below you will find the steps necessary to complete some of the most common dryer repairs.

Safety:

a) Before attempting any appliance repair disconnect the electrical power by removing the AC cord at the wall outlet. A small outlet can easily carry 150 times the current needed to kill a person.

b) Wear cut or tear resistant gloves to protect your hands. There are many sharp edges from sheet-metal that can easily draw blood dryer repair pasadena.

c) Use knee pads to save your knees from stain.

Prevention:

a) Proper maintenance and care is essential in keeping your dryer running efficiently. Improper care will cause your unit to overwork by using more electricity to keep you clothes dry than if properly maintained. By following these tips, you can prolong the life of your clothes dryer, prevent fires and avoid many costly repairs.

b) Make sure the Dryer feet are level to prevent an imbalance in the machine that may cause loud noises and added wear to the Dryer.

c) Empty the lint filter after use for efficient drying and fire prevention. Remove anything else that can impede good airflow. Do not forget to clean the back of the dryer where lint settles.

d) Vent your dryer to the outside, never vent it inside. Clean out exhaust vent system at least once a year to remove clogs or other obstructions that can impede good airflow. Never vent with plastic or vinyl. Many people hire a professional to do their venting and service their dryer yearly. Knowledgeable technicians can clean all interior and exterior dryer ducts to a smooth running system and help prevent fires. Note: The U.S. Consumer Product Safety Commission (CPSC) says fires associated with clothes dryers occur annually.

e) Do not place foam backed rugs, rubber or plastic shoes or other heat sensitive articles in dryers. Also, to prevent fires, do not place clothing or other items soiled with flammable substances like gasoline and alcohol. Check the pockets of clothes for crayons and other heat sensitive items that may ruin the other clothes.

f) Do not overload the dryer. This may eventually burn out the motor.

Component Replacement: Before starting any appliance repair task find the model number of your appliance. The dryer model number tag is located inside the door on the frame. On some of the Maytag models the tag is located on the back of the top console. Write down the model number and find the parts breakdown diagram on an online parts supply website.

Igniter Replacement: Symptoms of a defective flame igniter includes: tumbling clothes without heat, excessive time drying and/or intermittent heat.

a) Locate the igniter on parts diagram.

b) Remove panels to gain access to the dryer igniter.

c) Remove the plug to the igniter and place the multimeter leads on each post of the igniter leads. Make sure your multimeter is on the ohms scale. If it measures “open” then replace the igniter. If it doesn’t measure “open” this does not guarantee the igniter is good. Igniters work on a safety principle. Current travels through the igniter to the gas valve. The gas valve is calibrated to open at a specified current. As the igniter burns hotter and hotter it decreases resistance allowing more current -flow to the gas valve until the threshold current is reached and gas flow occurs. Thus, you may measure a good ohms reading on a bad igniter that doesn’t burn hot enough.

d) Remove screws holding down the igniter, install new one, and tighten the screws. Be very careful when you’re doing this. The igniter element is very brittle and shatters easily. One small bump and you’ll be on your way to the appliance parts store to buy another igniter.

e) Re install panels and you should be ready to go. Test your dryer and hope that your replacement has fixed the problem.

Drum Roller Replacement: Symptoms of a defective drum roller include loud thumping and/or a squealing sound.

a) Locate the drum roller on the parts diagram.

b) Remove panels, drum belt and drum paying special attention detail. The parts will need to be re installed correctly when reversing the procedure.

c) Locate and replace the bad drum rollers. You may need a snap ring removal tool to do this. If this tool is not available you can use a small screwdriver to remove the snap ring.

d) Using light oil – 3 in 1 oil works fine – lube all the rollers before re assembly.

e) Reinstall Drum, Belt, and outer panels to complete the job.

Heater Element Testing and Replacement: Symptoms of a bad heater element include a dryer that does not heat. Drum will still turn.

a) Locate the location of the heater element on the parts diagram

b) Before replacing the heater element be sure it is defective. Switch the meter to the ohms scale and measure continuity between the two legs of the heater element. If it measures open then you’ve found the problem. Replace it. When removing old element make a mental note of all screws, thermostats, etc, that will need returned to their proper locations when new heater is installed.

c) Replace panels and turn on dryer to check functionality.

Training in Appliance Repair

Appliance repair engineers don’t by law have to hold any formal qualifications, just public liability insurance but as you can imagine, building a reputation when you’re working for yourself or finding employment in a reputable company is a whole lot easier if you do.

Being an appliance engineer is a great career choice for someone who wants flexibility in terms of working hours and location, someone who doesn’t want to be stuck in an office all day and someone who’s good with their hands. This criterion covers quite a lot of people in the UK, so as a consumer you’ll find that there’s a lot of choice out there when it comes to getting your appliance repaired and if you’re thinking of getting into it as a profession, formal training it what will set you apart kitchenaid dishwasher repair los angelesĀ .

It might be an idea to start with a short, introductory or evening course to see if the job really is for you and if it comes naturally before embarking on something more long term. These are widely available and the best place to look for these types of courses is online. Often these will be more of a taster than anything else and whilst they might provide some sort of certificate, it won’t count for much initially. What it will do is give you a stepping stone to something that’s widely recognised, like an NVQ in Appliance Repair or Engineering or put you ahead of the game if you’re going for an apprenticeship.

An NVQ (National Vocational Qualification) is a really great way to gain knowledge and practical experience of a specific area, which is perfect for those who know what they want to do or who are ramping up the number of qualifications in their portfolio with a view to starting a business or franchise offering a range of services.

NVQs are available in various levels so you can choose how far you want to take your training, obviously the further you go, the better it looks when you’re trying to build a customer base and become the best at what you do. They can also be done part time to fit around your job so you won’t be missing out on vital revenue while you study.

The other great way to learn on the job and build up relationships and customers as well as a good knowledge base is by applying for apprenticeships. These are no longer unpaid for those under 19 years old or those over 19 years but in their first year of an apprenticeships so they are a real option now.